Structural Analysis of Parking Barrier Made of Polymeric Resin Using Ansys Software
DOI:
https://doi.org/10.53893/ijrvocas.v2i4.175Keywords:
Barrier gate, Software ansys, Fibreglass, Polymeric foamAbstract
A barrier gate is a stopping tool that has a security function in a place such as an office or agency entrance. This study aims to examine the response of the beam structure of the polymer composite material due to the support test. The parking portal material in this research is BQTN 157 EX resin, MEKPO catalyst, fiberglass. There are two parking portal compositions with impact test heights of 2 m and 4 m which will be simulated with ansys software. Overall, from two types of compositions, namely polymeric reinforced fiberglass composition A and composition B by looking at the results of the equivalent stress distribution (von-mises), it is concluded that polymeric reinforced fiberglass composition A has a higher maximum stress than polymeric reinforced fiberglass composition. reinforced with fiberglass composition B. From the comparison between simulation and experiment, it is known that the composition of rod A has a different damage position between simulation and experiment. While the composition of rod B in the simulation of the same damage position occurs, namely in the crossbar area connected to the transmission shaft and the experimental also has a damage position in the crossbar area connected to the transmission shaft.
References
Ahmad, Lutfi. 2007. “Perancangan Portal (Palang Pintu) Masuk Kampus Universitas Muhammadiyah Malang”. [Skripsi] Malang: Universitas Muhammadiyah Malang.
Puji, H. 2013. “Desain Barrier Gate Dan Sistem Kontrolnya Untuk Sistem Parkir Ramah Lingkungan Berbasis Programmable Logic Control (PLC) Dan Scada”. [Skripsi] Semarang: Universitas Diponegoro.
Hestiawan, H., & Jamasri, K. 2017. “Pengaruh Penambahan Katalis Terhadap Sifat Mekanis Resin Poliester Tak Jenuh”. Teknosia, 3(1), 1-7.
Rudydwi. 2010. “Mengetahui Sifat Mekanik Material Dengan Uji Tarik”. https://rudydwi.wordpress.com/2010, diakses pada 25 April 2020 pukul 16.26.
Kristianto, Laurensius, 2018. Pengaruh Persentase Serat Fiberglass Terhadap Kekuatan Tarik Komposit Matriks Polimer Polyester. [Skripsi], Yogyakarta: Universitas Sanata Dharma Yogyakarta.
Kristianto, Laurensius, 2018. Pengaruh Persentase Serat Fiberglass Terhadap Kekuatan Tarik Komposit Matriks Polimer Polyester. [Skripsi], Yogyakarta: Universitas Sanata Dharma Yogyakarta.
Wennie Fransisca, Ismet Danial Nasution. 2015. Pengaruh Penambahan Serat Kaca Dan Serat Poliester Terhadap Kekuatan Impak Bahan Basis Gigitiruan Resin Akrilik Polimerisasi Panas. Vol 2. Nomor 1.
Moch. Razan Dwi, Djoko W. Karmiadji, Eko Prasetyo. 2020. Komposit Sandwich Hybrid Kombinasi Serat Tandan Kosong Kelapa Sawit Dan Serat Kaca Dengan Matrix Polyurethane, Vol.5.No.2.
Zulhanif, Investigasi Sifat Mekanik Material Komposit Yang Terbuat Dari Pemanfaatan Limbah Batubara Dengan Matrik Resin Poliester Tak Jenuh. Jurnal Mechanical, 1(1), 2010,
B. Syam, S Rizal. 2013. Pengembangan bahan komposit busa polimer (polymeric foam composite) diperkuat serat tandan kosong kelapa sawit (TKKS) untuk pembuatan berbagai produk industri transportasi dan olah raga. Final Report PENPRINAS MP3EI, DIKTI.
D Hastrino, M Muttaqin, B Syam, dkk. 2018 Analisa struktur speed bump paduan bahan concrete foam dan polymeric foam dengan variasi rongga menggunakan sofware Ansys 14.5. Talenta Conference Series: Energy and Engineering (EE) 1 (1), 104-108.
M Muttaqin. 2022 Static Simulation on Speed Bumps Made of Foam Concrete Foam with Durian Skin Fibers Using Ansys Software. Journal of Mechanical Engineering, Science, and Innovation 2 (1), 1-8.
REK Siregar, B Syam, B Wirjosentono, M Muttaqin. 2018 Static simulation to horse shoes alternative materials based basic polymeric foam reinforced fiberglass with ANSYS software.
Rios-Soberanis, C. R., R. H. Cruz-Estrada, J. Rodriguez-Laviada, dan E. Perez-Pacheco. 2012. Study of Mechanical Behavior of Textile Reiforced Composite Material. Engineering Journal DYNA: 115-123.
Nuzuli dan Syam Bustami, 2018. Concrete Foam Composite Production and Testing, Universitas Sumatera pp. 1-6.
S C, Liew. 2008. Pencirian Sifat Komposit Polimer Bergentian Semula Jadi Untuk Aplikasi Struktur, Master Thesis, Fakulti Kejuruteraan Awam Universiti Teknologi Malaysia.
Liwandy, Sinaga. 2021. “Analisa Kekuatan Bending Dan Tarik Statik Komposit Berbahan Dasar Polymeric Resin Diperkuat Serat Kaca Sebagai Bahan Alternatif Pembuatan Palang Komposit”. [Skripsi] Medan: Universitas Sumatera Utara.
Additional Files
Published
How to Cite
Issue
Section
License
Copyright (c) 2023 Zoanri Purba, Maraghi Muttaqin, Bustami Syam, Ade Irwan, Fakhrur Rozy
This work is licensed under a Creative Commons Attribution 4.0 International License.
